Posts made by Trevor

• 2.94 Firmware Update Issue Rec A BMS

  @Rick Just tested them all 5 minutes ago and they are good :( Was really hoping for an easy fix there

  posted in REC Active BMS

  T

  Trevor
  3/12/25, 2:24 PM
• 2.94 Firmware Update Issue Rec A BMS

  @Ben Morning Ben, I'm looking through the manual now but do not see where the internal fuse or cell balancing fuse are located, could you point me in the right direction? I didnt see one when I had...

  posted in REC Active BMS

  T

  Trevor
  3/12/25, 8:20 AM
• 2.94 Firmware Update Issue Rec A BMS

  @Trevor 

  posted in REC Active BMS

  T

  Trevor
  3/11/25, 2:25 PM
• 2.94 Firmware Update Issue Rec A BMS

  Alright guys: Just reformatted the Wifi module SD card and loaded up 2.95. I reset the internal clock battery on the Rec ABMS. Got it all put back together again and did the firmware update to 2.95...

  posted in REC Active BMS

  T

  Trevor
  3/11/25, 2:24 PM
• 2.94 Firmware Update Issue Rec A BMS

  @Trevor It won't let me send manual messages to update the SOC, and I'm not sure whats going on with the temp sensor. Individual cell voltages read normal when I go to that page, as well as the te...

  posted in REC Active BMS

  T

  Trevor
  3/9/25, 4:58 PM
• 2.94 Firmware Update Issue Rec A BMS

  @Rick Hey Rick I'm at my wits end with this thing, tried 2.94 again and followed the updated guide with no positive results. Back to 2.93 but now I'm getting errors, such as in the screenshot poste...

  posted in REC Active BMS

  T

  Trevor
  3/9/25, 4:56 PM
• New REC BMS and Victron Cerbo DVCC integration Guide

  How come when I enter "CHRG 1" my ABMS replies Error 1? Same response when I enter "CHRG?" "CANS 2" and "CANS?" work fine

  posted in REC BMS Tips and Tricks

  T

  Trevor
  3/9/25, 3:09 PM
• 2.94 Firmware Update Issue Rec A BMS

  @tom That's so bizarre, I'm about to revisit mine as well. I have just had it on 2.93 the last 6 months

  posted in REC Active BMS

  T

  Trevor
  3/8/25, 2:41 PM
• 2.94 Firmware Update Issue Rec A BMS

  @Ben Thank you, I tried again this morning and when I successfully install 2.94 the REC disconnects from the Cerbo, I don't know why. I switch back to 2.93 and it works perfectly.

  posted in REC Active BMS

  T

  Trevor
  9/15/24, 10:24 AM
• 2.94 Firmware Update Issue Rec A BMS

  @Rick I just reverted back to 2.93-1 and the REC immediately showed up on the Cerbo.

  posted in REC Active BMS

  T

  Trevor
  9/14/24, 10:19 AM
• 2.94 Firmware Update Issue Rec A BMS

  @Ben Hi Ben, yes the Send address for communication is set to 2 still. The system has been running great for over a year, it was just the update that changed something, can't figure out what it is.

  posted in REC Active BMS

  T

  Trevor
  9/14/24, 7:14 AM
• 2.94 Firmware Update Issue Rec A BMS

  @Rick It did not. On the Cerbo under BMS - Can port it's just reading REC: N/A

  posted in REC Active BMS

  T

  Trevor
  9/13/24, 6:24 PM
• 2.94 Firmware Update Issue Rec A BMS

  I just updated my Rec A BMS to 2.94, and immediately afterwards my Victron system lost communication with the Rec. I have a Cerbo GX, Multiplus 12/3000, Smart MPPT's, Samrt Shunt etc, all has been ...

  posted in REC Active BMS

  T

  Trevor
  9/13/24, 5:31 PM
• Error in Cell Voltage Reading and Sudden Voltage Drop

  @Rick Hi Rick I have not been able to resolve this other than narrowing it down to a faulty connection with the AMP connector. Is there a warranty that would replace the wirring harness?

  posted in REC Active BMS

  T

  Trevor
  5/31/24, 12:40 PM
• Error in Cell Voltage Reading and Sudden Voltage Drop

  Thanks @Rick. There are no A/C lines anywhere nearby. Would you mind explaining a bit more about network devices that might be causing a ground loop? I will take the connector off and check for ba...

  posted in REC Active BMS

  T

  Trevor
  5/13/24, 1:43 PM
• Error in Cell Voltage Reading and Sudden Voltage Drop

  I have a Rec Active BMS with a 3P4S EVE 308Ah setup on my sailboat. I installed the system last October, all 12 cells were top balanced to 3.65 before installing. About a month ago I noticed cell ...

  posted in REC Active BMS

  T

  Trevor
  5/12/24, 6:05 PM
• Beginners Questions about my 2P4S setup

  @Rick Hi thanks for your reply, I am currently building a 3P4S setup with EVE 304ah cells. Just checking to make sure the Rec Active BMS is fine with 3 cells in parallel as well? Thanks!

  posted in REC Active BMS

  T

  Trevor
  8/9/23, 6:50 PM