@Bill Haven't sent the file to AI yet. My plan was to test the latest firmware from REC and Wakespeed to see if it solved any problems. If you send data, it would be nice if you could share your fi...
Posts made by Jonny
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
Problem solved!.Have now solved most of the problems with regulation with good help from my supplier Trond at Farco. Pulsating regulation occurred due to NMEA conflicts, which I suspected in the fi...
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
Still having the same problem with pulsed charging. Now testing with REC fw 2_53 (volt regulation) and WS fw 2.5.3. Have deactivated RPM and now use RPM from nmea, as well as changed the feature i...
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
I have now tested charging over time and I definitely have something unstable in the system. Not sure what the cause is, but sometimes when I start the engine it regulates according to DVCC, other ...
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
I have now tested a bit with REC firmware 2_92 and WS firmware 2.5.3.Based on the analysis of data at low current <50A and it regulates up and down, I see that the RPM goes from 0 to 2300RPM (th...
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
Tine sent me firmware v2_93, but I can't get DVCC to work, even after a full restart of all devices. When I go back to v2_92, DVCC works again. I have sent an email and am awaiting a reply.Tested w...
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
@Trond Cells are perfectly balanced and copper rails between cells. Works well at power above 50A. Is in dialogue with REC, which confirms a challenge with current regulation. What I now use is vol...
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
Hi Trond, so nice to hear from you! I have followed you and Lars on Marinetraffic and hope it will soon be possible for me to travel too.Have you spoken to REC about this issue? In the past, Tine h...
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
It was an interesting hypothesis. I have serpentine belts on both dynamos and there is marginal stretch. I have run the WS-500 as a master in the past and it has worked fine, but it will probably b...
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
SOC is 64% and cells are perfectly balanced 0.003V difference.
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
Now I tested with a higher current and then it is stable. As you can see, the problem occurs when the power is below approx. 50A. Values statra then to chase very much. Attach various images show...
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
The LED is orange and the DVCC is working. Attach a picture, hope it can help.
-
WS-500 constantly regulates up and down.posted in WS500 User Installation and Programming Questions
Hi. I have challenges with regulating the WS500. I suspect NMEA conflicts, but I'm struggling to get an overview, and which unit I should change (instance). I have Cerbo-gx with os large (firmware ...
-
Configuration Tool for windowsposted in Software Configuration Tool
Solved the problem of buying an Android tablet:) Windows for REC, Android for WS and MAC for everything else. HTML or an app that is OS independent would be nice and avoid a number of user problems...
-
Configuration Tool for windowsposted in Software Configuration Tool
Thanks for the reply, but the problem is that I don't have access to the "NMEA advanced" menu when I use the WS 500 config tool for windows. I don't have an android phone and therefore don't have a...
-
Configuration Tool for windowsposted in Software Configuration Tool
Hi. Is it possible to access the "advanced" menu in the pc software for windows to set up ws500 to support DVCC? I have followed all the requirements in the manual but cannot access: NMEA2000...
Search
Latest topics
Latest posts
Forum statistics
- Page views (24h):
- 138
- Page views (30d):
- 2,747
- Topics:
- 351
- Posts:
- 1,892
- Members:
- 1,045
