Posts made by Adam

• Wakespeed on gx touch screen

  Quote from Trond Arvid Røsvik on August 9, 2022, 4:38 am I use currently the VE-CAN port only, set to 250 kbps. A-BMS->Cerbo->WS500->NMEA2000 to the boat. This works perfect.  An bo...

  posted in Software Configuration Tool

  A

  Adam
  10/28/22, 5:27 PM
• WS500 bench test

  Update: Well, the documentation seems a little misleading here.  The cables with label: (10) Battery Ground Sense (Black/Yellow Stripe) (11) Battery Positive Sense (Red/Yellow Stripe) &...

  posted in WS500 User Installation and Programming Questions

  A

  Adam
  10/28/22, 5:22 PM
• REC ABMS not recharging after reaching full charge

  I turned the MP3k back on and it did eventually begin to ramp down, however my cells were drifting apart pretty significantly, two around 3.53 and the other two down in the 3.4 range and dropping. ...

  posted in REC Active BMS

  A

  Adam
  10/27/22, 10:13 AM
• WS500 bench test

  And to test powered up, you need to have your battery + and - connected as well   Just to make sure I understand this, the Alt +/- AND the battery (sense?) +/- need to both be wired up for...

  posted in WS500 User Installation and Programming Questions

  A

  Adam
  10/27/22, 9:11 AM
• REC ABMS not recharging after reaching full charge

  Sorry, I tried to format the above for best readability, but it seems some of the styling did not take :(

  posted in REC Active BMS

  A

  Adam
  10/26/22, 1:35 PM
• REC ABMS not recharging after reaching full charge

  Hello,  Today I updated my REC ABMS to 2.8 software.  At the time, my pack was measuring around 72% (3.25v per cell), and had not been recharging.  After the upgrade, the pack was reading 50% (Th...

  posted in REC Active BMS

  A

  Adam
  10/26/22, 1:34 PM
• REC Pre-Charge module manual and/or wiring diagram

  Update: I received an updated 2.8 firmware for ABMS from Tine today, and it included a 2.8 manual which contains the updated diagram, which solves this all for me :)   Cheers

  posted in REC Active BMS

  A

  Adam
  10/25/22, 6:34 PM
• REC ABMS not recharging after reaching full charge

  Hmm.. I read this, did the math, and double checked my settings but I still do not understand why it is not recharging. In order to trigger a charge, I have to set the  \"END of charging voltage hy...

  posted in REC Active BMS

  A

  Adam
  10/24/22, 9:10 AM
• REC Pre-Charge module manual and/or wiring diagram

  Hello, Today I went to wire up my pre-charge module and noticed that the diagram in the latest REC ABMS Manual, as well as the lates REC Pre-Charge Module manual, illustrate what appears to be a...

  posted in REC Active BMS

  A

  Adam
  10/24/22, 9:06 AM
• REC ABMS not recharging after reaching full charge

  75.9% today, 13.27 volts, still no charging occurring ;( Also looks like I forgot to mention I am on 30A shore power at the moment.  MP3k is set to 100A charge limit

  posted in REC Active BMS

  A

  Adam
  10/21/22, 11:36 AM
• WS500 bench test

  I found this video from wakespeed where they show only plugging in the USB cable.  This worked for me!  

  posted in WS500 User Installation and Programming Questions

  A

  Adam
  10/20/22, 7:08 PM
• REC BMS WiFi firmware update 1.6 now released

  For the record, I did experience this a little bit after my upgrade, some of the values I entered would get submitted with the decimal in the wrong place, or omitted entirely.  It did not persist t...

  posted in REC Product Announcements

  A

  Adam
  10/20/22, 6:54 PM
• WS500 bench test

  I am trying to power on my WS500 to check firmware version, upgrade, and configure via my android.   I have bound the Ignition Wire (Brown) and Alternator Positive (Red) to +12v Alter...

  posted in WS500 User Installation and Programming Questions

  A

  Adam
  10/20/22, 6:44 PM
• WS500 sensors & REC BMS

  ahoy! I convinced myself that the balmar 618 was a waste of time and received the WS500 kit today.  I\'ve got a few questions around operating it in tandem with the REC BMS. From reading the ...

  posted in WS500 Tips, Tricks and support

  A

  Adam
  10/20/22, 5:40 PM
• REC ABMS not recharging after reaching full charge

  Hello, My system has been setup for a few days, and it is either not re-entering charge mode, or I dont know how to determine when it should be (i.e. an SOC level, a voltage level, etc.)  Most like...

  posted in REC Active BMS

  A

  Adam
  10/20/22, 5:11 PM
• Active BMS latest firmware?

  Hello, I was reading this thread on victrons forum and have a couple questions.  It looks like my BMS is currently running firmware v2.7 The linked thread mentions a version 2.8, as well as a \"...

  posted in REC Product Announcements

  A

  Adam
  10/15/22, 12:18 PM
• REC BMS WiFi firmware update 1.6 now released

  oh good, that sounds easy enough.  Will give it a shot. Thanks for the quick reply!   Update:  That worked! Thanks again!

  posted in REC Product Announcements

  A

  Adam
  10/15/22, 11:58 AM
• REC BMS WiFi firmware update 1.6 now released

  Today I put together my BMS and battery pack.  The wifi module was on firmware version 1.5.8.  I tried to use the REC-WiFi-module-Firmware-Update-1.6-HW2.0.zip to update my module.  Everything appe...

  posted in REC Product Announcements

  A

  Adam
  10/15/22, 11:24 AM