what kind of different inverter interfaces?
what kind of different inverter interfaces?
slightly off topic but is there a diagram like this that shows the REC ABMS integration in place of the victron bms?
It sounds like you tried to wire your cells while the harness was connected to the BMS. The maximum voltage potential across your cell monitors is 5V DC. If you were to connect your ground, then ...
In case other users need the answer: We had blown four fuses. There are six (?) in total. The REC only ships with two spares, so now we wait! The fuse you need is \"t3 15a 250v cq mst\". I...
Hi there, We\'ve got a REC ABMS, but we\'re having trouble getting it to start up. We\'ve wired everything up according to the diagram below and checked everything twice. When we hit the BMS ...
Hey Patrick, if you could share with us a summary of what you are trying to achieve with the 4 packs and maybe some sequences of operation or pseudo code, it would help us give you some meaningful ...
Finally finished my second battery build, although these are just minor capacity cells (20aH). Slightly different in that I have used the REC WiFi module instead of the Bluetooth Module. Lots to le...
Feedback from Tine of REC You can make 4 way circuits with small signal relays or optocouplers. NC output of the relay is used to power LED or alarm in case of the blown fuse.
The Lynx Distributor does not look like it supports CANBus but just uses a simple I2C or 1Wire interface on the RJ10 connector. The REC BMS supports the 1wire protocol for its temperature sensors ...
According to the Victron Lynx Distributor manual only the Victron Lynx Smart BMS can communicate to the Lynx Distributor. Is it possible to get the REC Q BMS to do work with it?
Hot off the presses from the Victron Energy Community website showing the WS500 as part of its total energy solution for 2021. Check out the Victron github page as posted on another forum page f...
Ok, the short answer is yes, with a caveat. The WS500 uses a different pin out than the standard VE cable and may put voltage on your network if trying to use a standard cable. There is an intern...
Hey Ryan, Here is the latest drawing that includes the WS500 from Victron hot off the press. I haven\'t even reviewed it in detail yet myself but thought it might be an interesting read for you...
I have a pretty extensive Victron setup and just recently connected it to my NMEA network via a ve.CAN -> NMEA cable. Can I take the ve.CAN bus network that is daisy-chained to many of my vic...
Thanks Rick for your comments and commitment. I am currently building my second 20aH battery, its just minimally breadboarded now. I have the two batteries connected to a Cerbo and find some int...
As it stands right now the REC architecture is designed in such a way that the Q series with a master controller that provides supervisory control and monitoring is the way to go for a complete int...
Hello I am interested in this posting. I will trying to connect 4 LFP batteries in parallel using 4 REC BMS units. My plan so far is to use a Victron BMS-712 battery monitor and/or a Victron Cer...
Thanks. Please let me know what REC says about the software being able to track two separate batteries/BMS\'s vs just 4 \"cells\".
Correct, you would just set each WiFi device to a single unit. I haven\'t tried it yet but it might be that your WiFi modules could each act as a backup, giving you redundancy at that level too. ...
Thank you for the info. Look forward to hearing what REC has to say. One additional sub question would be: If using two WiFi modules, would that allow for history logging from both devices? T...
Great question. First, the 2 BMS\'s can indeed share a WiFi module but they need to have their RS485 addresses set differently and then you can then just select the one to communicate with once ...
12v RV with the new Victron Multiplus II. Any issues with using a pair of the these BMS\'s in parallel? Considering having the redundancy of a pair of 2P4S batteries rather than just one 4P4S bat...
Hey Neil, There are two ways to limit the output on your alternator with a WS500. For low RPM you can add a factor which will reduce the output at lower RPM, provided you have your ...
I wanted to check if it is possible to cap the output amps of an alternator using the WS500 I want to use a high output alternator that has a really good output at low rpm on a single V belt but wa...
A new release of the WS500 configuration tool is now available. If you have a working installation you can order the free download here. https://www.offgridsoftwaresolutions.com/product/ws500-so...
That\'s likely a bit low and may generate a bit of heat. If you have lots, just put them in series in sets of 4 per drop, for a total of 32 (4x56 ohm= 224 ohms). Right in the range that Tine sugg...
@tine @rick_tech_support any issue with using something as low as 56 Ohm? I have a bunch laying around and was going to use them?
It looks like we were on the right track, because the resistance of each voltage divider resistor was so high they were affected by the internal impedance of the analog input circuitry. From Tin...
@rick_tech_support, thanks! Primoz at REC got back to me in the meantime with a suggestion that fixed the issue. Essentially the resistances on the \"battery simulator\" were too high. @tine, ...
Hey Nate, nice setup you have there! I went through your blog findings and we are going to have to punt this one back to REC but I suspect it\'s a relativity issue(resistor impedance vs internal...
Hi, I recently received my REC Q from you guys. Looks great! I\'m in the process of testing it in advance of installing it on my cells. I\'m seeing a voltage sensing anomaly on what would be c...
Quote from coryhall on April 9, 2021, 7:53 pm Thanks for the reply Rick, it would seem that I have power at the panel, I am now concerned with the ground somewhere. Not sure if it has anything do ...
Yes, both the 12V ABMS and the larger Q Series we sell both have the Victron and WS500 interfaces as standard. For different Inverter interfaces you would want to consider the SI series of REC B...
Is the unit you are selling the Victron Compatible one? Thanks much.
Thanks for the reply Rick, it would seem that I have power at the panel, I am now concerned with the ground somewhere. Not sure if it has anything do do with wire #5 not being on the back of the al...
The ignition switch power can be used to connect to the ignition input as it only draws a few milli-amps, (wire #1 on your WS500) but will not have power to drive the field circuit. This power co...
Hello, I lost any power to my Yanmar type B panel and kill switch in it. The regulator excite wire is not hooked up but it would seem it powers my yanmar panel and switch. Should I be hooking my o...
A current shunt works by having a short length of thinner conductor and measuring the voltage drop in millivolts across, so you have to ask which side is \"more\" negative. And since the negative b...
Hello, for sending wires, what side is the positive side on a shunt that’s on the negative wire to the batteries only?