@Rick I went through the steps just as you described them. Well, I cheated just a little on step 4. I didn't immediately walk away. I left the cover off the Wifi module so that it...
Posts made by Richard
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
@Rick I did try all three RS485 bitrates for the Wifi module. The re-flashed ABMS never responded. Since I couldn't unlock it, I couldn't load a program to it and issue commands, such a...
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
@Rick-admin Upgrading the Cerbo from 3.00 to 3.54 seems to have been the key. The ABMS now communicates with the Victron over the VE.CAN port. Thanks for your help. Everyth...
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
@Rick I've been trying to find the quick start manual you mentioned previously. Sorry for all the hand holding.
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
The bootstrapped ABMS never established comms with my Wifi unit - so I couldnt proceed further resurrecting that unit. I recieved and installed the replacement unit and wiring harness, which ...
-
Bricked ABMS?posted in REC Active BMS
I received the spare parts an installed the new wire loom with no effect. The new BMS worked immediately and communicated with the WiFi unit at the default 56k. The Canbus only function...
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
@Ben I bought a UEBSP programmer off of Trademe here in NZ. I wish I had bought a two-pack for a few more dollars. Why? Because you need a second programmer to update firmware on ...
-
Bricked ABMS?posted in REC Active BMS
Tine, I've verified that only the Firmware page is functional. All other pages on the Wifi interface simply say: "BMS not connected". I tried all 3 RS-485 link speeds on the Wifi ...
-
Bricked ABMS?posted in REC Active BMS
As I recall, the home page only displays a large "BMS NOT COMMUNICATING" message. I'm away from my boat for a few hours. I'll verify when I return.
-
Bricked ABMS?posted in REC Active BMS
There appears to be no communication between the BMS and WIFI module. On the firmware page I enter my unit serial number (1A-1720) to unlock communications. I get an "incorrect password...
-
Bricked ABMS?posted in REC Active BMS
My Wifi module, BMS, and Cerbo are all powered from the battery side of the contactor. They always have power. I will try setting the Wifi module RS485 speed to 56k and 115k. When I attempt...
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
Rick, you deserve the support admin of the year award for responding from North America at this hour!Thanks, but no luck with 1A-0000. I also tried a whole bunch of 7 character strings: ...
-
Bricked ABMS?posted in REC Active BMS
@o-firstname I recently flashed my ABMS and can't proceed to loading firmware from my Wifi module. It seems like the device serial number no longer acts as the password to unlock BMS communic...
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
@Rick I obtained an AVR programmer here in NZ and it was quick work to load the .hex and .eep files from @tine I've run into a problem unlocking the serial communication between my Wifi modul...
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
@Ben Read The Fine Manual is always good advice! I re-read the Ver. 2.94 ABMS manual. Regarding setup of the CAN port on the Victron GX device, it states: "Use BMS-Can port w...
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
@Rick and @Ben thank you very much for the advice on the BMS-CAN versus VE-CAN ports on the Cerbo. I remember agonizing over the choice between the two 3 years ago. Lacking guidance fr...
-
2.94 Firmware Update Issue Rec A BMSposted in REC Active BMS
My system has been working flawlessly for 3 years except for the Wifi module. For some reason, it will only function in Station mode. When I scan for networks, nothing happens. I'...
-
Unable to check unlisted settings using the WIFI moduleposted in REC Active BMS
I just wanted to report back to close out this issue. I was able to flash the latest Wifi module firmware and that fixed the problem.
-
What charging precedence strategy are you using with your REC-BMS-controlled-Victron-Energy-LiFePO4 marine system?posted in REC-BMS Programming and Configuration Questions
Bill, I've been living with a similar setup for several years but have no Wakespeed. I've found the Victron, without any "precedence" programming, does the right thing. If solar is put...
-
Unable to check unlisted settings using the WIFI moduleposted in REC Active BMS
Thanks again for your help Rick. I'm just now heading offshore, so I'm reluctant to flash it right now. When I get to broadband Internet again, in a month, I'll report back to you.
-
Unable to check unlisted settings using the WIFI moduleposted in REC Active BMS
Thanks for the quick reply and advice Rick! I got a little bit further.I'm now able to set variables and I receive the "OK" response. I think I wasn't using a leading zero previously.&n...
-
Unable to check unlisted settings using the WIFI moduleposted in REC Active BMS
I've been wanting to verify and adjust several unlisted settings such as RAZL. When I attempt to do so using the dialog box on the Firmware screen, I get no response. Not only that, but...
-
How to manage state of charge while on shore powerposted in REC Active BMS
I've created a Node-Red flow that solves this problem perfectly. It has a dashboard interface to enable/disable the scheme. It also sends an email when the Victron Multiplus mode is aut...
Search
Latest topics
Latest posts
Forum statistics
- Page views (24h):
- 224
- Page views (30d):
- 8,146
- Topics:
- 368
- Posts:
- 2,129
- Members:
- 1,057
